Skip to content

Help Centre

Search For Topics
< All Topics

BeamOS – Input/Output



Inputs and Outputs are used for the monitoring and controlling of a connected device or receiving signals from that device in order to trigger certain events. This chapter is an overview on the Input/Output section for BEAM routers.


This section provides a list Input/Output electric characteristics inherent in BEAM iSERIES routers:

  • Digital non-isolated input (DIN1): Logic low 0 – 5 V; Logic high 8 – 40 V
  • Digital open collector (OC) output: 30 V, 300 mA


The Status tab displays the current states the router’s input and output:

Networking manual input output status IO status screen

Custom Labels

If the default Input/Output labels do not suit your needs, you can always configure custom ones in the Custom Labels section. Click the ‘Edit’ button next to the desired Input or Output and you will be redirected to a window such as this:

Networking manual input output status custom label digital input screen

The figure above is an example of custom label configuration for Digital Input. You can change an input’s/output’s name and the names of their states. The changes are purely cosmetic and used for easier management purposes.

Status and control from command line

You can control and monitor input and output values via a command line interface (CLI) with the command. You can execute this command without any additional options to get usage syntax examples:

root@beam-onboard:~# GPIO control aplication Usage: /sbin/ <ACTION> <NAME> ACTION - set, clear, get, export, invert, dirout, dirin NAME - SIM MON MRST SDCS CASE DIN1 DOUT1


  • DIN1 – Digital input
  • DOUT1 – Digital output

For example, to get the status of the digital output use the following command:

root@beam-onboard:~# get DOUT1 0
The return value 0 means that the output is in Inactive (Low level), i.e., OFF. You can turn it ON (Active (High level)) by setting its value to 1:
root@beam-onboard:~# invert DOUT1 root@beam-onboard:~# get DOUT1 1
As seen in the example above, you can change the value of an output by using the invert command, which simply turns the current value of the specified output and turns it into its opposite state.


The Input tab is used to configure the router’s input pin.

Input Rules

The Input Rules section provides you with the possibility to set up rules that execute user specified actions after a certain trigger occurs. To add a new rule, look to the Input Configuration section that is just below. Select the input, the trigger and the action for the rule and click the ‘Add’ button. A new rule will appear in the Input Rules list:

Networking manual input rules add new screen
To begin editing an input rule, click the ‘Edit’ button located next to it. Refer to the figure and table below for information on input rule configuration.
Networking output input rules input configuration screen
Field Name
yes | no; default: yes
Turns the input rule on or off.
Input type
Digital; default: Digital
Selects to which input pin the rule will apply.
Input open | Input shorted | Both; default: Input open
Selects which input state will trigger the rule.
Send SMS | Send email | Change profile | Turn on WiFi | Turn off WiFi | Reboot | Activate output; default: Send SMS
The action that will be taken when the rule is triggered. Send SMS – sends an SMS message to a specified number(s) or user group. The message text is custom. Send email – sends an email to the specified address(es). You will be prompted to enter your email account’s authentication information. Change profile – switches to using another configuration profile. Configuration profiles can be created via the System → Profiles page. Turn on WiFi/Turn off WiFi – turns WiFi on or off. Reboot – reboots the router when a specified amount of time passes or instantly after the trigger occurrence. Activate output – activates the specified router output.


The Output tab is used to configure the router’s output pin.

Output Configuration

The Output Configuration section is used to change the default state of the router’s output pin.

Networking manual input output on off screen

Post/Get configuration

Enabling Post/Get will allow you to send HTTP POST/GET requests to the router that control the state of the output. The figure below is an example of the Post/Get configuration section an the table below provides information on the fields contained in that section:
Networking input output post get configuration screen
Field Name
yes | no; default: no
Turns Post/Get on or off.
string; default: none
Username used for authentication in POST/GET queries.
Post/Get examples

It is possible to turn the output on and off by using a valid HTTP POST/GET syntax. Use a web browser or any other compatible software to submit HTTP POST/GET strings to the device.

Below is a table containing syntax examples of this usage:

Turn output on
Turn output off
Turn output on after a 10 second delay
Turn output on for 5 seconds
Turn output on for 5 seconds after a 10 second delay


  • – router’s default LAN IP address; replace it in accordance with your own configuration.
  • username – login name from Post/Get configuration.
  • password- password from Post/Get configuration.
  • action- the action that will be performed on the output (can be on or off).
  • pin – specifies the output (use oc).
  • delay – defines a delay (in seconds) after which the specified action will be performed.
  • time – defines a window of time during which the action will take place. For instance, if you post an on action while specifying time=5, the output will turn on and stay on for 5 seconds before turning off.

Delay and time parameters can be used together. For example, if delay is 10, time is 5, action is on, then 10 seconds after the execution of the command, the output will switch to on (or stay in on state if it was already that way), then after 5 more seconds it will switch to off state. In this case the overall command execution time is 15 seconds.

Periodic control

The Periodic control section allows you to set up automatic output control rules that trigger output state changes at the specified period or interval. Refer to the figure and table below for information on configuration fields contained in that section.
Networking manual input output periodic control screen
Field Name
yes | no; default: no
Turns the rule on or off.
Digital OC output | Digital relay output; default: Digital OC output
The output pin that will be be effected by the rule.
On | Off; default: On
The action that will be performed on the output.
Action timeout
yes | no; default: no
When the rule will be triggered. Fixed – triggers the specified action on a specified day(s), hour and minute. For example, every Sunday at 8:30 AM. Interval – performs the action at an interval. For example, every 1 hour during Mondays.


With the help of the output Scheduler you can configure a timetable of when the output should be enabled or disabled based on time.
Networking input output scheduler screen
Previous BeamOS – QoS
Table of Contents
Stay in the know

Sign me up for Emails

Get our latest product updates, exclusive offers, and introductions to new services and support.