Skip to content

BeamOS – LAN


Summary #

A local area network (LAN) is a computer network that interconnects computers within a limited area such as a residence, school, laboratory, university campus, or office building. By contrast, a wide area network (WAN) not only covers a larger geographic distance but also generally involves leased telecommunication circuits or Internet links. An even greater contrast is the Internet, which is a system of globally connected business and personal computers.

This chapter is an overview of the beamOS  LAN section.

Configuration #

General Setup #

The General Setup tab provides you with the possibility to set the router’s Private IP address, IP netmask and IP broadcast.
Network lan configuration general screen

Field NameValueDescription
IP addressip; Default: address that the device uses on the LAN network
IP Netmaskip; Default: netmask is used to define how “large” the LAN network is
IP Broadcastip; Default: ” “IP broadcasts are used by BOOTP and DHCP clients to find and send requests to their respective servers
IPv6 Addressip; Default: ” “Assigns an Ipv6 address for this interface. CIDR notation: address/prefix
IPv6 Prefix Length ip; Default: 60Delegates a prefix length for this interface
IPv6 Subprefix Hintip; Default: ” “Hexadecimal hint to used in the IPv6 address prefix
ULA Prefixip; Default: ” “Prefix used for the Unique Local Address

Advanced Settings #

LAN Configurations Advanced Settings tab contains some less frequently used, more complicated configurations, such as custom MTUs and network interface metric values.
Network lan configuration advanced screen

Field NameValueDescription
Accept router advertisementsyes | no; Default: noAllows accepting router advertisements
Override MTUinteger [0..1500]; Default: 1500MTU (Maximum Transmission Unit) specifies the largest possible size of a data packet
Use gateway metricinteger; Default: 0The LAN configuration generates an entry in the routing table. In this field you can alter the metric of that entry. Higher metric means higher priority
Use WAN port as LANyes | no; Default: noIf this is enabled, the router’s WAN port will act as if it were a LAN port. Works only if WAN is not set to wired

DCHP Server #

A DHCP server is a service that can automatically configure the TCP/IP settings of any device that requests such a service (i.e., connects to the device with the operational DHCP server). If you connect a device that has been configured to obtain an IP address automatically, the DHCP server will lease out an IP address from the available IP pool and the device will be able to communicate within the private network.

General #

The General Setup tab is used to set DHCP server settings. The figure below is an example of the General Setup tab and the table below provides information on the fields contained in that tab:
Network LAN DCHP server general screen

Field NameValueDescription
DCHPEnable | Disable | DHCP Relay; Default: EnableEnables or disables DHCP Server. If DHCP Relay is selected, you will be prompted to enter an IP address of another DHCP server in your LAN. In this case, Whenever a new device connects to the router, the router will redirect any DHCP requests to the specified DHCP Server
Startinteger [1..253]; Default: 100The starting IP address value. e.g., if your router’s LAN IP is and your subnet mask is that means that in your network a valid IP address has to be in the range of [] ( is a special unavailable address). If the Start value is set to 100 then the DHCP server will only lease out addresses starting from
Limitinteger [1..4294967296]; Default: 150How many addresses the DHCP server can lease out. Continuing from the above example: if the start address is and the server can lease out 150 (default limit value), availabe addresses will be from to (100 + 150 – 1 = 249; this is because the first address is inclusive)
Lease timetime in ‘h’ (hours) or ‘m’ (minutes); Default: 12hThe duration of an IP lease. Leased out addresses will expire after the amount of time specified in this field and the device that was using the lease will have to request a new DHCP lease. However, if the device stays connected, its lease will be renewed after half of the specified amount of time passes, e.g., if the lease time is 12 hours, then every 6 hours the device will send a request to the DHCP server asking to renew its lease Lease time can be set in hours (h) or minutes (m). The minimal amount of time that can be specified is 2min (2m)

Advanced Settings #

You may also apply more complicated, less common configurations to your router’s DHCP Server in the Advanced Settings tab. The figure below is an example of the Advanced Settings tab and the table below provides information on the fields contained in that tab:
Network LAN DCHP server advanced screen

Field NameValueDescription
Dynamic DHCPyes | no; Default: yesEnables Dynamic allocation of client addresses. If this is disabled, only clients that have static IP leases will be served
Enable DNS rebind protectionyes | no; Default: yesEnables DNS rebind attack protection by discarding upstream RFC1918 responses (leave default unless necessary otherwise)
Forceyes | no; Default: noThe DHCP force function ensures that the router will always start it’s DHCP server, even if there is another DHCP server already running in the router’s network. By default the router’s DHCP server will not start when it is connected to a network segment that already has a working DHCP server
IP netmaskip; Default: your LAN netmask, thus making the DHCP server think that it’s serving a larger or smaller network than it actually is
DHCP OptionsDHCP options; Default: ” “Additional options to be added to the DHCP server. For example with ‘26,1470’ or ‘option:mtu, 1470’ you can assign an MTU value per DHCP.
You can add more options by clicking the plus symbol located next to the field
Force DHCP optionsyes | no; Default: noForces DHCP option to be sent even if its not requested

Static Leases #

Static IP leases are used to reserve specific IP addresses for specific devices by binding them to their MAC address. This is useful when you have a stationary device connected to your network that you need to reach frequently, e.g., printer, IP phone, etc.
Network LAN static leases screen

Field NameValueDescription
Hostnamestring; Default: ” “A custom name that will be linked with the device
MAC Addressmac; Default: ” “Device’s MAC address
IP Addressip; Default: ” “The desirable IP address that will be reserved for the specified device

IPv6 Server Configuration #

Field NameValueDescription
DHCPv6 serverEnabled | Relayed | Disabled; Default: EnabledState of DHCPv6 server
RA serverEnabled | Relayed | Disabled; Default: EnabledState of Router Advertisement server
NDP serverEnabled | Relayed | Disabled; Default: EnabledState of the Neighbour Discovery Protocol server
DNS serversstring; Default: ” “DNS servers advertised by the DHCPv6 server
Domain namesstring; Default: ” “Domain names advertised by the DHCPv6 server

IP Aliases #

IP Aliases are a way of defining or reaching a subnet that works in the same space as the regular network. This is useful if you need to reach the router that is located in the same network but in a different subnet. If you have a static IP configuration on your computer and don’t want to change it every time you need to reach a router in a different subnet, you can configure an IP alias in order to do so.

General Setup #

Network LAN IP alias general screen

Field NameValueDescription
IP Addressip; Default: ” “An alternate IP address used to reach the router by a device(s) that resides in the router’s LAN but has a different subnet
Netmaskip; Default: defines how “large” a network is

As you can see, the configuration is very similar to the static protocol; in the example above an IP address with a 99th subnet is defined. In this case, if some device has an IP in the 99th subnet (e.g., and the subnet’s gateway metric is “higher” and the device is trying to reach the internet it will reroute it’s traffic not to the gateway that is defined in common configurations but through the one that is specified in IP aliases.

Advanced Settings #

You may also define a broadcast address and a custom DNS server for your IP Aliases in the Advanced Settings tab.
Network LAN IP alias advanced screen

Field NameValueDescription
IP Broadcastip; Default: ” “IP broadcasts are used by BOOTP and DHCP clients to find and send requests to their respective servers
DNSip; Default: ” “A separate DNS server to be used by the IP Alias address
Gatewayip; Default: ” “A gateway is a network node that connects two networks using different protocols together

Relayd #

Relayd is a daemon to relay and dynamically redirect incoming connections to a target host. Its main purpose in RUT routers is extending the wireless network. For example, when RUT is in STA (Wireless Station) mode, it can be used to bridge WAN and LAN interfaces to create a larger Wireless network.

Field NameValueDescription
Enable yes | no; Default: noToggles Relayd ON or OFF

Powered by BetterDocs

Shopping cart



It only takes a few seconds